JQC-3FF DATASHEET PDF

Buy Xiamen Hongfa Electroacoustic JQC-3FF/12VDC-1ZS() only $ at Pushbutton Switches & Relays|Relays datasheet, inventory and pricing. Buy Xiamen Hongfa Electroacoustic JQC-3FF/ZST() only $ at Pushbutton Switches & Relays|Relays datasheet, inventory and pricing. Buy Xiamen Hongfa Electroacoustic JQC-3FF/HS only $ at EasyEDA components online store LCSC. Pushbutton Switches & Relays|Relays .

Author: Zurn Samumi
Country: Lebanon
Language: English (Spanish)
Genre: Software
Published (Last): 1 September 2009
Pages: 199
PDF File Size: 1.48 Mb
ePub File Size: 12.19 Mb
ISBN: 114-6-90743-199-2
Downloads: 89457
Price: Free* [*Free Regsitration Required]
Uploader: Migor

No large currents here, nothing to worry. I am interpreting the picture of the printed circuit board of the relay module with accompanying notes as follows:. Post Your Answer Discard By clicking “Post Your Kqc-3ff, you acknowledge that you have read our updated terms of serviceprivacy policy and cookie policyand that your continued use of the website is subject to these policies. Home Questions Tags Users Unanswered.

I’ll datashete tested wiring and relay using LED before posting.

Thank you very much for your answer, I hope this topic will be helpful for others too. You could easily check this with an Ohmmeter or following the traces on the board. Moreover, it even looks like relay board has diode already jqc3-ff VCC terminalso I wouldn’t need extra diode on IN line?

I am interpreting the picture of the printed circuit board of the relay module with accompanying notes as follows: If it does – no need for any external components. This voltage is consistent with the operating voltage on datasheeh relay”.

I know people recommend having resistor and transistor on IN line too, but are these necessary in this particular type of relay? On the Arduino side there is: Normally open, which means that when the relay is on a digital high “1” is received from Arduino the device is ON. So, using Datssheet a “1” will turn on the device and a “0” will turn off the device. Sending a digital low or “0” will disable the relay. Sign up or log in Sign up using Google.

  MANDE MUSIC ERIC CHARRY PDF

Xiamen Hongfa Electroacoustic JQC-3FF/HS – PDF Datasheet – Relays In Stock |

Sign up using Email and Password. Signal Vcc Ground On the appliance side there is: By clicking “Post Your Answer”, you acknowledge that you have read our updated terms of serviceprivacy policy and cookie policyand that your continued use of the website is subject to these policies.

The relay in use is: From the trace on the board it would seem that the middle resistor 1 kOhm is attached to the “IN” pin serving exactly this purpose. By using our site, you acknowledge that you have read and understand our Cookie PolicyPrivacy Policyand our Terms of Service.

I’ve tested components on board and can confirm it has: Sign up using Facebook. Do I need to add anything else for relay to work safely and reliably?

Above is relay I’m using and everything works as expected using diagram below. The diagrams below should help you understand the layout of the relay board. Please be vary carful not to play with live circuits! Email Required, but never shown. As Ghanima was a bit more explicit I’ve marked his answer as accepted. Cut and strip a portion of the positive wire so that you end up with two ends of the wire as shown in Figure 2.

  13 STEPS TO MENTALISM FILETYPE PDF

Thank you for the answer. We recommend using a swappable cable to do this with, as using a relay requires you to perform some minor surgery on the appliance’s cable.

Retrieved from ” https: Using single 5V relay jqc-3ff-s-z – safety advice required Ask Question. The relay should have the positive wire of the device being used connected to “IN” and to “Out 1” as shown datasneet figure 2, and any digital signal pin on the arduino end For example pin We will datasehet “out1” for our example, using “out2” will simply reverse the logic, as explained above. Post as a guest Name. Make sure the appliance to be tinckered with is unplugged from mains.

This page was last modified on 13 Juneat Discussion View source History.

Tutorial: DFR0017 V2 Relay

Sending a digital high or a “1” will trigger the relay. I understand such a question can sound silly for electrical engineer, but I’m software engineer venturing in electrical world and need some guidance.

Normally closed, which means that when the relay is off a digital low “0” is received from Arduino the device is ON Out1: