CCNP TSHOOT 6.0 INSTRUCTOR LAB MANUAL PDF

CCNP ROUTE Instructor Lab Manual. use by instructors in the CCNP TSHOOT course as part of an This lab uses Cisco routers with Cisco IOS. CCNP TSHOOT Student Lab Manual. Share? CCNP Routing and Switching TSHOOT Official Cert Instructor Lab Manual. Download Ccnp Tshoot Instructor Lab Manual free pdf, Download Ccnp Tshoot ccnp tshoot instructor lab manual. this document is exclusive property of.

Author: Tojall Duzragore
Country: Mozambique
Language: English (Spanish)
Genre: Love
Published (Last): 26 June 2010
Pages: 286
PDF File Size: 16.55 Mb
ePub File Size: 4.29 Mb
ISBN: 642-1-23443-995-5
Downloads: 95662
Price: Free* [*Free Regsitration Required]
Uploader: Faugal

Lab Debrief Notes Use this space to make notes of the key learning points that you picked up during the lab debrief discussions with your instructor.

To remedy this situation, configure the following commands on DLS1: The major Network Layer tests are ping and traceroute to a specific IP address.

By default, ARP entries are cached for four hours. Discuss mznual different teams used different commands and how each of those commands revealed information about the network. However, if the switches that you are using have the capability to track packet statistics for access lists, you might be able to write an access list that matches the specific traffic that you are interested in and isolate the traffic statistics for that type of traffic.

Consider assigning it as homework.

Suggested actions and results presented during the troubleshooting process for each TT can be shared with the students during debrief or copies of the instructor version of the lab can be made available to the students to assist them in verifying their work.

Edge for edge PortFast ports. Do not assign either PC a static address. Responsibilities can be reassigned during later labs if necessary. The team member who has primary responsibility for a device is in control of the console of that device and changes to the device.

  HP PAVILION 500 094L PDF

Other routers such as andswitches such as orand Cisco IOS Software versions can be used if they have comparable capabilities and features.

However, to regain the redundancy that is inherent in the physical network design, both issues must be diagnosed and resolved. If time is a consideration, each task or trouble ticket can be performed independently.

CCNP TSHOOT 6.0 Student Lab Manual

From the PC-B command prompt, issue the tracert command to router R2 loopback 0 at Review the logical lab diagram and the subnets. If the actual traffic path is different from your expected path, this step might give you clues about the particular links or protocols that are failing and the cause of these failures. For the same VLAN 10 that was referenced in the previous output, you now see interface port channel 1 and port channel 2 listed as ports that are associated with VLAN The following details are important to point out: However, not all students might have the skills to independently map and analyze the network.

This is your primary opportunity to document a baseline of the lab network before starting the troubleshooting exercises. The first entry for VLAN 10 is filled in as an example. Displays the spanning-tree mode and the VLANs for which this switch is the root bridge.

It lists all essential parameters that affect the topology, such as the root port, designated ports, port state, and port type.

It gives you a starting point for gathering information about what is actually happening on the network, and it makes it easier to spot abnormal behavior. The output also indicates which other type of STP was detected on the port. These can be downloaded from the Academy Tshooot web site. If the team consists of three people, each person can analyze and document instructof router and one switch. However, this command does not list the trunk ports.

  BLISTAVO I STRANO PDF

The notes can include problems encountered, solutions applied, useful commands employed, alternate solutions, methods and processes, and procedure and communication improvements.

Refer manua TT-C debrief for more information. With hundreds or thousands of hosts attached, access devices such as Layer 2 switches are a common source of networking issues.

ccnp_tshoot_instructor_lab_manual

Load the Baseline Device Configuration Files Use the following procedure on each device in the network to load the baseline configuration. If the directory 60. files are not present, contact your instructor. Determining the expected traffic path beforehand helps you in two ways: If the documentation does not provide this information, you can usually reconstruct the expected flow of traffic by analyzing network diagrams and configurations.

This lab uses tftpd32 for both TFTP and syslog. Another useful option is show mac-address-table interface mabual, which tshoott which MAC addresses were learned on a specific port. A very straightforward check after you have determined the expected path of the traffic is to verify that all ports and links in the path are operational. For each task or trouble ticket, the scenario and symptoms are described.

Add these to your toolbox for future use. Rather than try to list all the sthoot of configurations for each router class, this table includes identifiers for the possible combinations of Ethernet and serial interfaces in the device. Which other commands could you use to identify Layer 1 and Layer 2 characteristics? Even if you cannot find the underlying cause of the problem yourself, by reducing the scope of the problem, you have a better-defined problem that can be escalated to the next level of support.