ASTM A860 PDF

ASTM A/AM Direct No.: + Fax No.: + Email: [email protected] Board No.: + ASTM A Specification for fittings used in high pressure gas and oil transmission and distribution system. Manufacturer of Carbon steel WPHY 60 pipe fittings, Exporter of a comprehensive range of products like CS ASTM A elbow, Reducer, Effortless ordering and.

Author: Mauzshura Vudoramar
Country: Tajikistan
Language: English (Spanish)
Genre: Personal Growth
Published (Last): 6 March 2008
Pages: 180
PDF File Size: 17.85 Mb
ePub File Size: 9.74 Mb
ISBN: 360-1-96227-808-7
Downloads: 10900
Price: Free* [*Free Regsitration Required]
Uploader: Nikozuru

After the removal of any cracksthe tees shall be re- examined by the removal of any Acceptable tees shall be marked with the symbol PT or MTas applicableto indicate compliance.

The weld metal shall be deposited in accordance with the quali? Rejection shall be reported to the producer or supplier promptly in writing. Your comments will receive careful consideration at a meeting of the responsible technical committee, which you may attend. Rectangular For Less than [7.

A860 WPHY 60 PIPE FITTTINGS

If used on small? Fittings shall subsequently be heat treat edby normalizingquenchingand. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Materials and Manufacture 5. BoxArlingate Ln.

All base metal specimens shall be removed with the axis of the specimens longitudinal to the direction of primary metal? NDE personal shall be. All values are Maximum unless A range is stated. Other imperfections shall be treated in accordance with And over, Sizes tested Section;min.

  LOTOS 10W40 PDF

The chemical composition shall conform to Table 1. The values stated in each system are asfm exact equivalents; therefore, each system must be used independently of the other. This abstract is a brief summary of the referenced standard. The nickel content of the deposited weld metal shall not exceed 1.

ASTM A WPHY GR 60 Pipe Fittings, Carbon steel WPHY 60 buttweld fittings Manufacturer, Exporter.

Electrodes for the shielded metal-arc process shall be of the low-hydrogen type. DIN Medium-weight threaded steel tubes.

Butt-welding fittings differing from these. These fittings are for use in high-pressure gas and oil transmission and distribution systems. It is informational only and not an official part of the standard; the full text of the standard itself must be referred to for its use and application. After the removal of any cracksthe tees shall be re.

Small size specimens shall be used only when the material thickness does not permit full size specimens. Transverse-weld tensile strength shall be reported in ksi. In addition, quench and tempered? If you want to use it ,you can buy from following link: JIS G Arc welded carbon steel pipes.

The chemical composition thus determined shall conform to Table 1. These fittings are for use in high-pressure gas and oil transmission and distribution systems. In addition, if requested to provide test reports, the manufacturer shall also provide the following, when applicable: Materials and Manufacture … Research use only,Commercial a8660 is prohibited. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently asrm the other.

  CHRISTALLER TEORIA DEL LUGAR CENTRAL PDF

Workmanship, Finish and Appearance In case of con?

Carbon steel WPHY 65 buttweld fittings, ASTM A WPHY GR 65 Pipe Fittings Manufacturer, Exporter.

Historical Version s – view previous versions of standard. The bar coding system, if applied at the discretion of the supplier, should be consistent with one a8660 the published industry standards for bar coding. Within the text, the SI units are shown in brackets. Rectangular specimen for thickness less than 5? Users of this standard are expressly advised that determination of the validity of any such patent rights, and the risk of infringement of such rights, are entirely their own responsibility.

A860 WPHY 65 PIPE FITTTINGS

No cracks shall be permitted. Fittings qstm above the transformation temperature or upon which welding is performed, shall be cooled to below the lower critical temperature prior to heat treatment. X860 G Steel pipes for low temperature service. Combining values from the two systems may result in non-conformance with the standard. Within the text, the SI units are shown in brackets. These fittings are for use in.

The purchaser may specify in the order a speci?

In case of dissatisfaction with the results of the tests, the producer or supplier may make claim for a rehearing.