24LC16B DATASHEET PDF

Description: The Artship Technology Inc. 24LC16B (24XX16*) is a Kbit Electrically Erasable PROM. The device is organized as eight blocks of X 8- bit. serial interface. Low voltage design permits operation down to volts with standby and active currents of only 5 µA and 1 mA respectively. The 24LC16B also. 24LC16B Datasheet, 24LC16 2kx8(16k) Serial CMOS EEPROM Datasheet, buy 24LC

Author: Makasa Gardakasa
Country: Djibouti
Language: English (Spanish)
Genre: Technology
Published (Last): 14 July 2007
Pages: 296
PDF File Size: 15.8 Mb
ePub File Size: 4.82 Mb
ISBN: 669-2-65148-660-2
Downloads: 94669
Price: Free* [*Free Regsitration Required]
Uploader: Kazrajind

24LC16B1 DATASHEET

Sign In or Register to comment. So that means, not only is it limited to only one of those devices, but only one of any device, right?

On the other hand, on page 6 where the control byte is explained, they say that the 24pc16b bits in the control byte are used to select one of the eight word blocks of the memory. Thanks for your help! I am looking to have possible 4 sx’s set up as slaves, and 1 eeprom and one rtc all set up on the same i2c bus if thats possible.

In the end, this solution my be even cheaper as one 24LC64 replaces four 24LC16 chips, and there is no need for some “tricky” decoding. Where none of the Micochip equivalents do address decoding at all. Perhaps you consider using 24LC64 chips instead.

  INTEL 80C32 PDF

24LC16B Technical Data

Quick Links Categories Recent Discussions. Let’s say I have an sx set up as a slave on that same bus, and i would like to send some info to only the sx, I could set the address to some abritrary number, but the eeprom would answer to any address, correct?

This doesn’t mean that you couldn’t use more than 24lcc16b chip, simply that you cannot use the multiple IC2 address protocall. Nate, I was just curious, and got the ST datasheet for their 24C Addressing of the devices is performed by sending a control byte via the bus.

In these datasheets they also state that the address pins are not connected. Hey, you can find the datasheet for the 24LC16 here: A while ago, I have developed a system similar to this with up to 5 SXes on one bus.

A 24CL16 with all three address pins connected to Vss would acknowledge the control byte x, and one with A0 connected to Vcc and A1, A2 connected to Vss would acknowledge the control byte x, etc. So it would be getting all of the bytes sent to it also. I use the 24LC64 in some of ratasheet SX applications with no problems.

John, fortunately, this is not the case. Maybe, this explains the difference. They definitely allow for datashset devices on a bus, and they have two address bytes following the control byte in order to address the full range of the memory.

  LON GONTRAN DAMAS PIGMENTS PDF

Nate, this is strange.

Seems as if there actually can only datxsheet one 24LC16 on a bus without additional decoding. But I could successfully verify that the chips decode the status of the address pins. In this system, each of the SXes could act as master and slave, therefore I also had to handle bus arbitration but it worked nicely in the end.

Gunther, Page 11 of said datasheet states that A0, A1, and A2 are 224lc16b connected in this device. I realise that i could probably set the write protect pin of the eeprom, but i would rather just get a different xatasheet. As the address following the control byte is only 8 bits wide, three additional bits are required to cover the full address space of bytes.

24LC16B Datasheet(PDF) – Microchip Technology

Comments 9 Comments sorted by Date Added Votes. Their 01 and 02 devices actually have the three address bits 24cl16b, the 04 device has two bits decoded, the 08 device just one, and the 16 device none at all. I did not use the 24LC16 so far but “smaller” devices, like the 24LC Nate Post Edited Nate: